Skip to content

Unit 1 of 7

Kinematics

12.5% of the exam124 reviewed questions21 key terms17 min read

Kinematics is worth about 12.5% of the AP Physics 1 exam. Our bank tests it with 124 reviewed questions across 21 distinct ideas — 15 easier, 92 medium and 17 harder.

On this page · 12 sections

Kinematics describes motion without asking what causes it. You track three quantities over time: position, velocity and acceleration. Each one is the rate of change of the one before it. Velocity is how fast position changes, and acceleration is how fast velocity changes. Nearly every question in this unit comes down to moving between those three, whether the motion is given as numbers, as an equation, as a graph or as a sentence.

The unit builds in layers. First you separate scalars from vectors, so you know why a car that drives 60 m east and 20 m west has gone 80 m but is only 40 m from where it started. Then you use the constant-acceleration equations and motion graphs, where slopes and areas carry the physics. Free fall is the same idea with the acceleration fixed at g, about 9.8 m/s² downward on Earth and about 1.6 m/s² on the Moon. Projectile motion puts two of those one-dimensional problems side by side, constant velocity sideways and free fall up and down, joined only by shared time. Relative motion closes the unit by asking who is doing the measuring.

This unit is about 10–15% of the exam, but it supports everything that follows. Unit 2 on forces asks you to find acceleration from a velocity graph. Energy and momentum problems often need a speed or a time of flight first. If you can switch fluently between a graph, an equation and a description of the same motion, the rest of the course gets easier.

The unit in a minute

One line per topic. Tap any line for the full notes.

  1. Distance versus displacementAdd all legs for distance; add them with signs for displacement, and expect the choices to swap them.
  2. Velocity, acceleration and the sign of aSpeeding up or slowing down depends on whether v and a point the same way, not on the sign of a alone.
  3. The constant-acceleration equationsChoose the equation that skips the unknown you don't need, and use squared terms to reason about ratios.
  4. Reading position-time and velocity-time graphsSlope of x-t is velocity, slope of v-t is acceleration, and the height of v-t is velocity, not position.
  5. Area under the velocity-time curveArea under v-t is displacement; areas below the axis subtract for displacement and add for distance.
  6. Free fall on Earth and the MoonFree fall means a = g downward at every instant, and height and flight time both scale as 1/g.
  7. Projectile motion: launch angle, components and maximum heightSplit the velocity, solve horizontal and vertical separately, and connect them only through time.
  8. Relative motion and relative velocitySubtract velocities to change observers, and add them as vectors when motions are perpendicular.
Grind Kinematics questionsAlready know this? Skip the notes and prove it.

The big ideas

Vectors keep track of direction, and scalars do not

Distance and speed are scalars, so they count every meter and never cancel. Displacement, velocity and acceleration are vectors, so motion in opposite directions subtracts. Before you write any equation, pick a positive direction and stick to it. With up as positive, a ball thrown upward has a positive velocity and a negative acceleration at the same moment, and that is not a contradiction. Most wrong answers in this unit come from dropping a sign or from treating a vector as if it were a scalar.

Slopes and areas link the three graphs

The slope of a position-time graph is velocity. The slope of a velocity-time graph is acceleration. The area under a velocity-time graph is displacement, and the area under an acceleration-time graph is the change in velocity. So one graph lets you build the other two. If you can read a slope and add up an area, you can answer most graph questions without any equation.

Constant acceleration makes motion predictable

When acceleration does not change, three equations describe everything: v = v₀ + at, x = x₀ + v₀t + ½at², and v² = v₀² + 2aΔx. Each one leaves out one variable. You choose the equation that skips the quantity you were not given and do not need. Free fall is just this case with a = −g. These equations fail when acceleration changes, which is why a graph sometimes has to be split into pieces.

Perpendicular motions are independent

Horizontal and vertical motion do not affect each other. Gravity pulls only downward, so with no air resistance a projectile's horizontal velocity never changes, while its vertical velocity changes by g every second. The one thing the two directions share is time. That is why a bullet fired level and a bullet dropped from the same height hit the ground together. Solve each direction on its own, then connect them through t.

Motion depends on the observer

Every velocity is measured relative to something, usually the ground. A passenger walking forward on a moving train has one velocity relative to the train and another relative to the platform. You find the velocity of A relative to B by subtracting: v(A rel B) = v(A) − v(B). This idea comes back in momentum and collisions, where choosing a convenient reference frame can make a hard problem simple.

Study notes

8 topics. Each one opens with its key idea, then the detail you need to use it.

1. Distance versus displacement

Key idea: Add all legs for distance; add them with signs for displacement, and expect the choices to swap them.

Distance is the total length of the path you travel. It is a scalar, so every leg adds no matter which way you go. Displacement is the straight-line change in position from start to finish, Δx = x_final − x_initial. It is a vector, so legs in opposite directions partly cancel.

Take a car that drives 90 m east and then 25 m west. The distance is 90 + 25 = 115 m. For displacement, call east positive: +90 + (−25) = +65 m, so the car ends 65 m east of its start. The two answers match only when the object moves in a straight line without changing direction. In one dimension, that means it never reverses. A path that turns also breaks the match: 3 m east then 4 m north is 7 m of distance but only 5 m of displacement. A runner who completes one 400 m lap has covered 400 m of distance but has zero displacement.

The same split applies to rates. Average speed is distance divided by time. Average velocity is displacement divided by time. If that lap takes 80 s, the average speed is 5 m/s and the average velocity is 0 m/s. On the exam, the wrong choices almost always contain the right numbers in the wrong places. So label each number as path or net change before you look at the choices. Neither quantity is ever found by averaging the legs or halving the total.

2. Velocity, acceleration and the sign of a

Key idea: Speeding up or slowing down depends on whether v and a point the same way, not on the sign of a alone.

Velocity is the rate at which position changes, including direction. Acceleration is the rate at which velocity changes: a = Δv/Δt. If a car goes from 2 m/s to 10 m/s in 4 s, its acceleration is (10 − 2)/4 = 2 m/s². The unit m/s² means the velocity changes by that many m/s every second.

The sign of acceleration does not tell you whether an object is speeding up. What matters is how a compares with v. When velocity and acceleration point the same way, the object speeds up. When they point opposite ways, it slows down. A car moving in the negative direction with a negative acceleration is speeding up, even though a is negative.

Acceleration can also be nonzero when velocity is zero. A ball thrown straight up stops for an instant at the top, but gravity is still changing its velocity at 9.8 m/s² downward. If the acceleration were zero there, the ball would hang in the air forever. Questions about the highest point test exactly this. At the top, the velocity is zero and the acceleration is still g downward.

3. The constant-acceleration equations

Key idea: Choose the equation that skips the unknown you don't need, and use squared terms to reason about ratios.

When acceleration is constant, you can predict the motion with three equations. v = v₀ + at has no Δx in it. Δx = v₀t + ½at² has no final velocity. v² = v₀² + 2aΔx has no time. List what you know and what you want, then pick the equation that leaves out the quantity you don't have.

Suppose a car moving at 25 m/s brakes at 5 m/s² until it stops. Take the direction of motion as positive, so a = −5 m/s². Time to stop: 0 = 25 + (−5)t, so t = 5 s. Stopping distance: 0 = 25² + 2(−5)Δx, so Δx = 62.5 m. You can check this with average velocity. Under constant acceleration, the average velocity is (v₀ + v)/2 = 12.5 m/s, and 12.5 m/s × 5 s = 62.5 m.

The v² equation explains a common result. Stopping distance grows with the square of speed, so doubling the speed makes the stopping distance four times as long. Multiple-choice questions often ask about ratios like this instead of asking for a number. Write the equation, see which variable is squared, and scale it.

4. Reading position-time and velocity-time graphs

Key idea: Slope of x-t is velocity, slope of v-t is acceleration, and the height of v-t is velocity, not position.

On a position-time graph, the slope at any point is the velocity at that moment. A straight line means constant velocity. A steeper line means faster motion. A flat line means the object is at rest. A curved line means the velocity is changing. If the curve bends upward like a cup, the acceleration is positive. If it bends downward like a cap, the acceleration is negative.

On a velocity-time graph, the slope is acceleration. A line from 2 m/s up to 10 m/s over 4 s has slope 2 m/s², so the acceleration is 2 m/s². A horizontal line means zero acceleration, not zero velocity. Where the line crosses the time axis, the object turns around because its velocity changes sign.

The most common graph error is reading the height of a velocity-time graph as a position. A velocity graph that slopes downward but stays above the axis describes an object still moving forward, only more slowly. To compare two objects at one instant, decide first whether the question asks for a slope or for a value. On a position graph, the value is position and the slope is velocity. On a velocity graph, the value is velocity and the slope is acceleration.

5. Area under the velocity-time curve

Key idea: Area under v-t is displacement; areas below the axis subtract for displacement and add for distance.

The area between a velocity-time graph and the time axis equals the displacement. The reason is simple. For a short time interval, displacement is velocity times time, which is a thin rectangle of height v and width Δt. Adding up all those rectangles gives the total area.

Work with shapes. Suppose an object speeds up from 0 to 12 m/s in 4 s and then cruises at 12 m/s for 2 more seconds. The first part is a triangle: ½ × 4 × 12 = 24 m. The second part is a rectangle: 2 × 12 = 24 m. The total displacement is 48 m. A trapezoid works the same way, as the average height times the width.

Area below the time axis counts as negative displacement, because the object was moving in the negative direction. To get displacement, subtract the area below the axis from the area above it. To get distance, add both areas as positive numbers. The same rule works on an acceleration-time graph, where the area is the change in velocity. If a question gives you an acceleration-time graph and a starting velocity, add the area to the starting velocity to find the final velocity.

6. Free fall on Earth and the Moon

Key idea: Free fall means a = g downward at every instant, and height and flight time both scale as 1/g.

An object in free fall moves only under gravity, so its acceleration is g downward the whole time. That holds whether it is rising, at the top or falling. Near Earth's surface g ≈ 9.8 m/s², and many problems let you use 10 m/s², so check the directions. With no air resistance, mass has no effect, so a bowling ball and a marble dropped together land together.

Use g ≈ 10 m/s² and drop a stone from rest. After 1 s it falls at 10 m/s and has dropped 5 m. After 2 s it falls at 20 m/s and has dropped 20 m. Distance grows with t², so each second it covers more ground than the last.

Now throw a ball straight up at 20 m/s. It loses 10 m/s every second, so it reaches the top after 2 s. The maximum height comes from v² = v₀² − 2gh with v = 0: h = 400/20 = 20 m. The trip down mirrors the trip up, so the ball lands 4 s later at 20 m/s downward.

On the Moon, g is about 1.6 m/s², roughly one-sixth of Earth's. Time to the top is v₀/g, and maximum height is v₀²/2g. So the same throw rises about six times higher and stays up about six times longer.

7. Projectile motion: launch angle, components and maximum height

Key idea: Split the velocity, solve horizontal and vertical separately, and connect them only through time.

A projectile is free fall with a sideways velocity added. First split the launch velocity into components: v_x = v cos θ and v_y = v sin θ, where θ is measured from the horizontal. For 20 m/s at 30°, v_x = 17.3 m/s and v_y = 10 m/s. Check yourself: an angle under 45° always gives a larger horizontal component.

Next, treat each direction separately. Horizontally there is no acceleration, so x = v_x t. Vertically the acceleration is −g, so the vertical part acts exactly like a ball thrown straight up at v_y. With g ≈ 10 m/s², the 30° ball reaches its highest point after 1 s, rises 5 m and lands after 2 s. Its range is 17.3 × 2 ≈ 35 m. At the highest point only the vertical velocity is zero. The ball still moves sideways at 17.3 m/s, so its speed is not zero.

For a horizontal launch, v_y starts at zero. A ball rolling off a 5 m high ledge at 3 m/s falls for √(2 × 5/10) = 1 s and lands 3 m out. Rolling it off faster changes how far it goes, not how long it falls.

On level ground, range is R = v₀² sin 2θ / g, which peaks at 45°. Complementary angles such as 30° and 60° give the same range, but the 60° shot goes higher and stays up longer.

8. Relative motion and relative velocity

Key idea: Subtract velocities to change observers, and add them as vectors when motions are perpendicular.

A velocity only has meaning when you say what it is measured against. To find the velocity of object A as seen by observer B, subtract: v(A rel B) = v(A) − v(B), where both are measured against the ground. Pick one positive direction first.

A car drives east at 60 km/h and a bus drives west at 40 km/h. With east positive, the bus passenger sees the car moving at 60 − (−40) = 100 km/h east. Objects moving toward each other close at the sum of their speeds. If the bus were also heading east at 40 km/h, the passenger would see the car pull ahead at only 20 km/h.

In two dimensions, you add velocities as vectors. A boat aims straight across a river at 4 m/s while the current flows downstream at 3 m/s. Its velocity relative to the shore is 5 m/s at an angle downstream. The current does not slow the crossing, because it is perpendicular to the boat's heading. An 80 m wide river takes 80/4 = 20 s, and in that time the boat drifts 3 × 20 = 60 m downstream.

To land directly across, the swimmer or boat must aim partly upstream. The upstream component has to cancel the current exactly. A swimmer who moves at 3 m/s in a 2 m/s current must aim upstream at an angle θ from the straight-across direction, where 3 sin θ = 2. The crossing speed then drops to 3 cos θ = √5 ≈ 2.2 m/s, so the trip takes longer than it would in still water.

Common mistakes

Drawn from the wrong answers students actually pick on these questions.

Putting the right numbers in the wrong slots, so the net change in position is reported as the distance and the total path is reported as the displacement.

Distance is always the larger number (or equal) because it never cancels. For 60 m east then 20 m west, the distance is 80 m and the displacement is 40 m. Label each number before you match it to a choice.

Adding both legs when finding displacement, as if the westward leg also pointed east.

Displacement is a vector sum. Give the reversed leg a negative sign: +80 m + (−30 m) = +50 m. Displacement equals distance only if the object never changes direction.

Subtracting legs to get distance, or averaging or halving the legs to get either quantity.

Distance never cancels, so you always add the leg lengths. Neither distance nor displacement comes from averaging. A choice like (90 + 25)/2 is a trap built from a step that matches no definition.

Saying the acceleration is zero at the highest point because the object stops there.

At the top, the vertical velocity is zero but gravity still acts, so the acceleration is still g downward. If it were zero, the object would stay at the top.

Thinking a projectile's horizontal velocity slows down during flight, or that its speed is zero at maximum height.

With no air resistance, nothing acts horizontally, so v_x stays constant. At maximum height only v_y is zero. The speed there equals v_x, which is the minimum speed of the flight but not zero.

Reading the height of a velocity-time graph as position, or assuming a downward-sloping v-t line means the object is moving backward.

On a v-t graph the height is velocity and the slope is acceleration. A line that falls but stays above the axis means the object is still moving forward and slowing down. It reverses only where the line crosses zero.

How this unit shows up on the exam

Kinematics makes up about 10–15% of the multiple-choice section of the AP Physics 1 exam, and its ideas appear in problems from every later unit. In the multiple-choice section, the questions have four options. Expect short calculation items, like finding total distance and displacement for a two-leg trip, or acceleration from the slope of a velocity-time graph. The wrong choices are built from predictable errors: swapped quantities, a dropped minus sign, or an averaged value. So decide what each number means before you look at the options. Many items need no calculation at all. They ask for a ratio, such as how stopping distance changes when speed doubles. They also ask which graph matches a description, or what is true at a projectile's highest point. Typical stems read "which of the following best describes" or "how does the time of flight compare."

The free-response section uses kinematics constantly. A Mathematical Routines question may have you find a projectile's range or maximum height and then derive a symbolic expression in terms of v₀, θ and g. A Translation Between Representations question may give a description and ask you to sketch position-time and velocity-time graphs that match it, with consistent slopes, sign changes and turning points. An Experimental Design and Analysis question might ask how to measure g with a motion sensor or a dropped object, and then have you linearize data. Graphing distance against t² gives a straight line with slope ½g. A Qualitative/Quantitative Translation question asks you to argue in words and then check the argument with an equation. A typical task is explaining why two balls launched horizontally at different speeds land at the same time.

Readers reward clear reasoning. State the positive direction. Write the equation before you substitute numbers. Keep units and signs on every value. When you justify a claim, name the physics, for example that horizontal and vertical motions are independent and that both objects have the same vertical acceleration and starting vertical velocity. A correct number with no reasoning often earns less credit than a clear argument with a small arithmetic slip.

How the exam actually asks it

Real items from the AP Physics 1 bank, easier first. The answer is marked, and every wrong choice is explained — because knowing why a distractor is tempting is most of the work.

Worked example 1Easier
A car travels 60 m east and then 20 m west. What are the total distance traveled and the magnitude of the displacement?
  1. A40 m and 80 m
  2. B80 m and 40 mCorrect
  3. C80 m and 80 m
  4. D40 m and 40 m

Why B is right

Distance is a scalar that counts every meter of the path, so the total distance is 60 m + 20 m = 80 m. Displacement is a vector from the start point to the end point. Taking east as positive, it is +60 m + (-20 m) = +40 m, so its magnitude is 40 m. The answer is 80 m and 40 m (B).
Why the other 3 choices miss
A
Incorrect. This swaps the two quantities: 40 m is the net displacement and 80 m is the total path length, so the order is reversed.
C
Incorrect. This uses the total path length for displacement as well, adding the 20 m west leg instead of subtracting it because it points in the opposite direction.
D
Incorrect. This uses the net displacement for distance as well. Distance counts the 20 m driven back west instead of cancelling it.
Worked example 2Easier
A car travels 80 m east and then 30 m west. What are the total distance traveled and the magnitude of the displacement?
  1. A50 m and 110 m
  2. B110 m and 50 mCorrect
  3. C110 m and 110 m
  4. D50 m and 55 m

Why B is right

Distance is a scalar, so it adds up every segment of the path: 80 m + 30 m = 110 m. Displacement is a vector from the start to the end. With east as positive, the net change in position is (+80 m) + (-30 m) = +50 m, so the magnitude is 50 m (east). The answer is 110 m and 50 m, choice (B).
Why the other 3 choices miss
A
Incorrect. This swaps the two quantities. 50 m is the net change in position (displacement), and 110 m is the total path length (distance), not the reverse.
C
Incorrect. This treats displacement like distance by adding the magnitudes of both legs. That ignores that the 30 m west leg points opposite to the 80 m east leg.
D
Incorrect. This gives the net displacement (50 m) as the distance. It then gives half the total path (110/2 = 55 m) as the displacement, but neither quantity is found by halving.
Worked example 3Easier
A car travels 50 m east and then 10 m west. What are the total distance traveled and the magnitude of the displacement?
  1. A40 m and 60 m
  2. B60 m and 40 mCorrect
  3. C60 m and 60 m
  4. D40 m and 30 m

Why B is right

Distance is the total path length, whatever the direction, so it is 50 m + 10 m = 60 m. Displacement is the net change in position. Take east as positive: Δx = (+50 m) + (−10 m) = +40 m, so the car ends 40 m east of where it started. The answer is 60 m of distance and a 40 m displacement, choice B.
Why the other 3 choices miss
A
Incorrect. This swaps the two quantities. The net 40 m is the displacement, not the distance, and the total path of 60 m is the distance.
C
Incorrect. This treats displacement like distance and adds the 10 m westward leg instead of subtracting it. Motion in the opposite direction reduces the net change in position.
D
Incorrect. This subtracts the legs to get the distance (40 m), but distance never cancels. The 30 m displacement matches no combination of the given values. The correct displacement is 50 − 10 = 40 m.
Worked example 4Easier
A car travels 40 m east and then 15 m west. What are the total distance traveled and the magnitude of the displacement?
  1. A25 m and 55 m
  2. B55 m and 25 mCorrect
  3. C55 m and 55 m
  4. D25 m and 28 m

Why B is right

Distance is a scalar that counts every meter of path traveled, whatever the direction: 40 m + 15 m = 55 m. Displacement is the net change in position. Take east as positive: +40 m + (-15 m) = +25 m, so the car ends 25 m east of where it started and the magnitude of the displacement is 25 m. The answer is 55 m and 25 m (B).
Why the other 3 choices miss
A
55 m and 25 m are the right numbers, but they are swapped: 25 m is the net displacement, not the distance, and 55 m is the total path length, not the displacement.
C
This adds the two legs as if both pointed east, so the westward 15 m is treated as positive. That gives the distance, but not the displacement, which has to account for the reversal in direction.
D
The 25 m is the net displacement used in place of the distance, and 28 m looks like the average of the total path (55 / 2 ≈ 28 m). Neither step matches the definition of either quantity.

Can you do all of these?

Tick what you can do without looking. Anything left unticked is where to go back to.

0 of 10 ticked

Ready to test yourself?

Open practice pulls from the 22 free questions in this unit. The other 102 come with the one-time AP purchase, which unlocks every AP course.

Official topic list

The official course framework breaks this unit into 5 numbered topics.

  1. 1.1Scalars and Vectors in One Dimension
  2. 1.2Displacement, Velocity, and Acceleration
  3. 1.3Representing Motion
  4. 1.4Reference Frames and Relative Motion
  5. 1.5Vectors and Motion in Two Dimensions

Key terms in Kinematics

Ordered by how often our reviewed questions test them. Open any term to see the questions that use it.

The rest of AP Physics 1

Every unit with its share of the exam. You are on Unit 1.

  1. 1Kinematics12.5% of exam
  2. 2Force and Translational Dynamics20.5% of exam
  3. 3Work, Energy, and Power20.5% of exam
  4. 4Linear Momentum12.5% of exam
  5. 5Torque and Rotational Dynamics; Energy and Momentum of Rotating Systems19% of exam
  6. 6Oscillations6.5% of exam
  7. 7Fluids12.5% of exam