Skip to content

Unit 7 of 7

Fluids

12.5% of the exam57 reviewed questions8 key terms16 min read

Fluids is worth about 12.5% of the AP Physics 1 exam. Our bank tests it with 57 reviewed questions across 8 distinct ideas — 11 easier, 46 medium and 0 harder.

On this page · 12 sections

A fluid is anything that flows: a liquid like water or a gas like air. In this unit you do not track single molecules. You treat the fluid as one continuous material and describe it with three quantities: density (how much mass sits in each cubic meter), pressure (how hard the fluid pushes on each square meter of surface) and flow speed. Almost every question reduces to one of these three ideas, or to a link between them.

The unit is really a replay of the course you already know. Buoyancy is Newton's second law with one extra force, so you draw a free-body diagram, add an upward buoyant force and set the net force to zero or to $ma$. The continuity equation is conservation of mass for a moving fluid. Bernoulli's equation is conservation of energy written per unit volume. Pascal's principle is the reason a hydraulic lift multiplies force, and it works because pressure in a fluid at rest depends only on depth.

The chain of ideas runs in one direction. Density sets how fast pressure grows with depth, through $P = P_0 + \rho g h$. The pressure difference between the top and bottom of a submerged object, acting over the object's area, produces the buoyant force: $F_b = \Delta P \cdot A = \rho_{fluid} V g$. Comparing the object's density to the fluid's density then tells you whether it sinks, floats, or hangs in place. If you can follow that chain on a diagram, you can handle most of the unit.

The unit in a minute

One line per topic. Tap any line for the full notes.

  1. Density: mass divided by volume, with units checkedDivide mass by volume, then ask whether the number is believable next to water at 1.0 g/cm³ or 1000 kg/m³.
  2. Pressure: force per area, and the gauge versus absolute splitUse $P = F/A$ for any surface, and read the stem carefully to tell whether it wants gauge or absolute pressure.
  3. Hydrostatic pressure: why depth is the only thing that countsPressure in a still fluid depends only on depth and density, $P = P_0 + \rho g h$, never on container shape.
  4. Pascal's principle and the hydraulic liftEqual pressure on both pistons multiplies force by the area ratio, but the distance shrinks by the same ratio, so work is conserved.
  5. Buoyant force and Archimedes' principle$F_b$ uses the fluid's density and the displaced volume, and it is one more force in your Newton's second law equation.
  6. Floating, sinking and the fraction submergedFor a floating object, buoyant force equals weight, and the fraction submerged equals the object's density divided by the fluid's density.
  7. Continuity and Bernoulli: fluids in motionNarrow pipe means faster flow by $A_1 v_1 = A_2 v_2$, and in a level pipe faster flow means lower pressure by Bernoulli.
Grind Fluids questionsAlready know this? Skip the notes and prove it.

The big ideas

Density is the property that controls everything else

Density is mass per volume, $\rho = m/V$, measured in kg/m³ or g/cm³. Water is about 1000 kg/m³, which equals 1.0 g/cm³. Density is a property of the material, not of the sample, so cutting a block in half leaves its density unchanged. Density shows up in the pressure-depth equation, in the buoyant force, in the floating rule and in Bernoulli's equation. When a question compares two fluids or two objects, check density first.

Pressure is force spread over area, and in a fluid it grows with depth

Pressure is $P = F/A$, measured in pascals, where 1 Pa equals 1 N/m². A fluid at rest pushes perpendicular to every surface it touches, in every direction. The deeper you go, the more fluid sits above you, so the pressure rises by $\rho g h$. That is why the shape of a container does not matter, only the vertical depth below the surface does.

Buoyancy is just another force on a free-body diagram

A submerged object feels more pressure on its bottom than on its top, so the fluid pushes it up harder than it pushes it down. The net result is the buoyant force, $F_b = \rho_{fluid} V_{disp} g$, which equals the weight of the fluid the object pushes aside. You add it to your force diagram next to gravity, tension or the normal force, then apply Newton's laws as usual.

Moving fluids obey the conservation laws you already know

Mass is conserved, so the same volume per second passes every point in a pipe. That gives $A_1 v_1 = A_2 v_2$, which is why the fluid speeds up where the pipe narrows. Energy is conserved too, so a fluid that speeds up or rises must lose pressure. Bernoulli's equation, $P + \tfrac{1}{2}\rho v^2 + \rho g y = \text{constant}$, is that energy bookkeeping written per cubic meter of fluid.

Study notes

7 topics. Each one opens with its key idea, then the detail you need to use it.

1. Density: mass divided by volume, with units checked

Key idea: Divide mass by volume, then ask whether the number is believable next to water at 1.0 g/cm³ or 1000 kg/m³.

Density tells you how tightly mass is packed into a space, and you find it by dividing mass by volume, $\rho = m/V$. A 240 g sample that fills 200 cm³ has a density of 240 ÷ 200 = 1.2 g/cm³, a bit denser than water. The exam asks this directly, and the wrong answers are built from predictable slips. One distractor is just the mass with density units stuck on, such as 240 g/cm³, while another is just the volume, such as 200 g/cm³. A third is off by a factor of 10, which comes from shifting a decimal or converting in the wrong direction.

Two habits protect you from those traps. First, sanity-check against water at 1.0 g/cm³ and remember that almost no liquid is denser than mercury at 13.6 g/cm³, so an answer of 240 g/cm³ for a liquid is absurd. Second, learn the conversion between unit systems: 1 g/cm³ equals 1000 kg/m³, so a liquid at 1.2 g/cm³ is 1200 kg/m³. You will need kg/m³ whenever density goes into $\rho g h$ or $F_b = \rho V g$ with SI units. The conversion works because 1 m³ holds a million cm³ while 1 kg is only a thousand grams, which leaves a factor of 1000.

Density is an intensive property, so it does not depend on how much of the material you have: double the volume of oil and you double its mass, but $m/V$ stays the same.

2. Pressure: force per area, and the gauge versus absolute split

Key idea: Use $P = F/A$ for any surface, and read the stem carefully to tell whether it wants gauge or absolute pressure.

Pressure is the force a surface feels divided by the area that force is spread over, $P = F/A$. A 120 N force spread across 0.02 m² gives 120 ÷ 0.02 = 6000 Pa. Because area is in the denominator, a small area makes a large pressure, which is why a thumbtack goes into a board while your flat palm pushing with the same force does not.

Pressure itself is a scalar, and a fluid at rest pushes perpendicular to any surface in contact with it, whether that surface faces up, down or sideways. The force on a surface is a vector, $F = PA$, and the direction of that force is set by which way the surface faces.

You need to keep two kinds of pressure apart in every problem. Absolute pressure is the total pressure, including the atmosphere pressing on the fluid's surface. Atmospheric pressure at sea level is about $1.0 \times 10^5$ Pa, or 100 kPa, and gauge pressure is the extra pressure above the atmosphere, $P_{gauge} = P - P_0$. A tire gauge reads gauge pressure, which is why a flat tire reads zero even though the air inside still pushes at 100 kPa. When a question says "gauge pressure" it wants $\rho g h$ alone, but when it says "absolute" or "total" pressure, add $P_0$.

3. Hydrostatic pressure: why depth is the only thing that counts

Key idea: Pressure in a still fluid depends only on depth and density, $P = P_0 + \rho g h$, never on container shape.

Picture a column of fluid of height $h$ and area $A$ sitting on a small patch at the bottom. The column's mass is $\rho A h$, so its weight is $\rho A h g$, and dividing that weight by the area gives the extra pressure the column adds: $\rho g h$. Adding the surface pressure, the total pressure at depth $h$ is $P = P_0 + \rho g h$, where $P_0$ is the pressure at the surface.

For water, $\rho g$ is about 1000 × 10 = 10,000 Pa per meter, so the gauge pressure is 20 kPa at 2 m deep. At 10 m deep it reaches 100 kPa, which means the absolute pressure there is about 200 kPa, double the surface value. That 10-meters-doubles rule is a fast check on any water answer.

The equation contains no area and no container shape, so a thin tube and a wide lake filled to the same depth have the same pressure at the bottom. Every point at the same depth in one connected, still fluid has the same pressure, which is why water levels match in connected tubes. Exam questions test this with oddly shaped containers and ask you to rank pressures at labeled points, so rank by vertical depth below the surface and nothing else. Horizontal position and the width of the container above a point do not matter.

4. Pascal's principle and the hydraulic lift

Key idea: Equal pressure on both pistons multiplies force by the area ratio, but the distance shrinks by the same ratio, so work is conserved.

Pascal's principle says that a pressure change applied to an enclosed fluid is passed on undiminished to every part of the fluid and to the walls. If you push on a sealed syringe, the pressure rises by the same amount everywhere inside it, not just near the plunger. This follows from hydrostatics. In a still fluid, the pressure difference between any two points is fixed at $\rho g \Delta h$. So if the pressure at one point rises by $\Delta P$, the pressure at every other point has to rise by the same $\Delta P$ to keep those differences.

A hydraulic lift puts this to work, because a small piston of area $A_1$ and a large piston of area $A_2$ share one body of fluid. Pressing with force $F_1$ raises the pressure by $F_1/A_1$, and the large piston feels that same pressure. Setting the two pressures equal, $F_1/A_1 = F_2/A_2$, which gives $F_2 = F_1 (A_2/A_1)$. If the big piston has 50 times the area, a 200 N push can hold up a 10,000 N car.

The lift does not create energy, though. The fluid volume pushed down on the small side must equal the volume pushed up on the large side, $A_1 d_1 = A_2 d_2$. As a result the small piston moves 50 times farther than the large one, and work in equals work out, since $F_1 d_1 = F_2 d_2$. The exam often asks for one force and then asks how far the other piston moves, so expect to use both relations.

5. Buoyant force and Archimedes' principle

Key idea: $F_b$ uses the fluid's density and the displaced volume, and it is one more force in your Newton's second law equation.

Any object in a fluid feels an upward buoyant force equal to the weight of the fluid it displaces. This is Archimedes' principle, and the formula is $F_b = \rho_{fluid} V_{disp} g$. The cause is pressure: the bottom of the object is deeper than the top, so the fluid pushes up on the bottom harder than it pushes down on the top, and since the sideways pushes cancel, a net upward force is left.

The formula uses the fluid's density, not the object's. A steel ball and a wooden ball of the same volume, both held fully underwater, feel exactly the same buoyant force because they push aside the same volume of water. Their weights differ, so the steel sinks while the wood, once released, floats up.

Once an object is fully submerged, the buoyant force stops changing as it sinks deeper. Both the top and bottom pressures rise by the same amount, so their difference stays fixed, although this only holds if the fluid density stays constant, which is a safe assumption for water in AP problems.

Apparent weight follows straight from a force diagram. Suppose you hang a 30 N rock from a spring scale and lower it into water. If it displaces 0.001 m³ of water, the buoyant force is 1000 × 0.001 × 10 = 10 N. The scale reads $T = mg - F_b$ = 30 − 10 = 20 N, but the rock did not get lighter, because the water is now carrying part of the load.

6. Floating, sinking and the fraction submerged

Key idea: For a floating object, buoyant force equals weight, and the fraction submerged equals the object's density divided by the fluid's density.

Whether an object sinks or floats comes down to two densities. When the object is fully under the surface, its weight is $\rho_{obj} V g$ and the buoyant force is $\rho_{fluid} V g$. The volume and $g$ cancel, so you only need to compare densities. If the object is denser than the fluid it sinks, and if it is less dense it rises to the surface. Equal density means it hangs in place at any depth, which is called neutral buoyancy.

A floating object is in equilibrium, so the buoyant force equals its weight exactly, and writing that out gives $\rho_{fluid} V_{sub} g = \rho_{obj} V g$. Rearranged, the fraction under the surface is $V_{sub}/V = \rho_{obj}/\rho_{fluid}$, so ice at 920 kg/m³ floats in water at 1000 kg/m³ with 92% of its volume below the waterline, and a block of 600 kg/m³ wood floats 60% submerged.

This rule explains several common exam setups. If you move a floating boat from fresh water into denser salt water, it rides higher because it needs less displaced volume to make the same buoyant force. The buoyant force itself does not change, since it still equals the boat's weight. If you push a floating block fully under with your finger, you have to supply the difference between the full buoyant force and the weight. If you put a heavy load on a raft, it sinks lower until the extra displaced water balances the extra weight.

7. Continuity and Bernoulli: fluids in motion

Key idea: Narrow pipe means faster flow by $A_1 v_1 = A_2 v_2$, and in a level pipe faster flow means lower pressure by Bernoulli.

For an ideal fluid that cannot be compressed, the volume entering a pipe each second must leave it each second. The volume flow rate is $A v$, cross-sectional area times speed, measured in m³/s, so $A_1 v_1 = A_2 v_2$ anywhere along the pipe. If you halve the area, the speed doubles. Area depends on radius squared, so halving a pipe's diameter cuts its area to a quarter and makes the speed four times greater. That squaring is where many students lose the point.

Bernoulli's equation adds energy to the picture: along a streamline, $P + \tfrac{1}{2}\rho v^2 + \rho g y$ stays constant. The middle term is kinetic energy per unit volume, and the last is gravitational potential energy per unit volume. That means that in a level pipe, wherever the fluid speeds up, the pressure must drop. The faster fluid gained kinetic energy, and the only place it could come from is the work done by a pressure difference pushing it forward.

A standard result comes from a tank with a hole a depth $h$ below the surface. The surface and the jet are both open to the air, so the pressure terms cancel, and if the surface drops slowly, energy conservation gives $v = \sqrt{2gh}$. That is the speed of an object dropped from height $h$, which is a good way to remember it.

Common mistakes

Drawn from the wrong answers students actually pick on these questions.

Reporting the mass or the volume as the density, such as answering 240 g/cm³ for a 240 g, 200 cm³ sample.

Density needs both numbers, so divide mass by volume, 240 ÷ 200 = 1.2 g/cm³. Treat any liquid density far above mercury's 13.6 g/cm³ as a sign of an arithmetic error, because no common liquid is that dense.

Getting a density 10 times too big or too small by shifting the decimal or converting in the wrong direction.

Estimate before you calculate: 240 is a little more than 200, so the answer must be a little more than 1. For SI conversions, remember that 1 g/cm³ is 1000 kg/m³, so the kg/m³ number is always the bigger one.

Using the object's density in $F_b = \rho V g$, so a steel ball seems to get a bigger buoyant force than a wooden ball of the same size.

The buoyant force uses the fluid's density and the displaced volume. Equal volumes fully submerged in the same fluid feel equal buoyant forces, whatever they are made of.

Thinking the buoyant force keeps growing as a submerged object sinks deeper, because pressure rises with depth.

Pressure rises on the top and bottom by the same amount, so their difference is unchanged. Once fully submerged, $F_b$ stays constant in a uniform fluid.

Mixing up gauge and absolute pressure, such as giving 120 kPa when the stem asks for gauge pressure at 2 m in water.

Gauge pressure is $\rho g h$ alone, 20 kPa here. Add atmospheric pressure, about 100 kPa, only when the question wants absolute or total pressure.

Assuming a hydraulic lift gives you free energy, or forgetting the area ratio uses radius squared.

The force grows by $A_2/A_1$, but the small piston moves farther by the same ratio, so work in equals work out. If the radius triples, the area and the force ratio go up ninefold.

How this unit shows up on the exam

Fluids carries roughly 10 to 15 percent of the AP Physics 1 exam. Multiple-choice items tend to fall into three kinds. The first is a direct calculation: density from a mass and volume, pressure from a force over an area, or gauge pressure from $\rho g h$. These are quick points if your units are clean, and the wrong options are built from the slips listed above. The second is a ranking or comparison question: rank the pressure at four points in a tank, or decide which of two blocks feels the larger buoyant force. The third asks what happens when something changes, such as a boat moving into salt water or a pipe narrowing.

Free-response questions fold fluids into other units. You may have to draw a free-body diagram of a submerged block on a string, write Newton's second law with the buoyant force included, and then derive an expression for the tension. You may also be asked to design an experiment to measure a liquid's density with a spring scale and a known object. A question on a pipe may want you to use continuity and Bernoulli together and justify in words why the pressure drops.

Scoring guidelines consistently reward three things. They want the fluid's net push drawn once, as a single buoyant force, and not added a second time as a separate "pressure force" arrow. They want a symbolic derivation that starts from a named principle such as $F_{net} = ma$, $A_1 v_1 = A_2 v_2$ or Bernoulli. They want justifications that name the physical cause, such as "the bottom is deeper, so it feels a greater pressure", not a formula alone.

How the exam actually asks it

Real items from the AP Physics 1 bank, easier first. The answer is marked, and every wrong choice is explained — because knowing why a distractor is tempting is most of the work.

Worked example 1Easier
A sample of liquid has a mass of and a volume of . What is its density?
  1. A
  2. BCorrect
  3. C
  4. D

Why B is right

Density is mass divided by volume: , which is choice B.
Why the other 3 choices miss
C
Incorrect. This uses as if it were density, instead of dividing by volume.
D
Incorrect. This uses as if it were density, instead of dividing mass by volume.
A
Incorrect. This is 10 times too large and usually comes from converting units in the wrong direction.
Worked example 2Easier
A sample of liquid has a mass of and a volume of . What is its density?
  1. A
  2. BCorrect
  3. C
  4. D

Why B is right

Density is mass divided by volume: , which is choice B.
Why the other 3 choices miss
A
Incorrect. This is 10 times too large and usually comes from converting units in the wrong direction.
C
Incorrect. This uses as if it were density, instead of dividing by volume.
D
Incorrect. This uses as if it were density, instead of dividing mass by volume.
Worked example 3Easier
A 120 N force is applied uniformly over an area of 0.02 m^2. What pressure is produced?
  1. A120 Pa
  2. B0.02 Pa
  3. C6000 PaCorrect
  4. D12000 Pa

Why C is right

Pressure is force divided by area: P = F / A = 120 / 0.02 = 6000 Pa. The result follows from the fluid relationship or pressure/flow equation given in the problem. The result follows from the fluid relationship or pressure/flow equation given in the problem, so the pressure or force difference gives the answer.
Why the other 3 choices miss
A
Incorrect. This treats force as pressure and ignores the area over which the force acts.
B
Incorrect. This uses the area as if it were the pressure.
D
Incorrect. This is a common arithmetic error from dividing by a different area or dropping a zero.
Worked example 4Easier
A 150 N force is applied uniformly over an area of 0.03 m^2. What pressure is produced?
  1. A150 Pa
  2. B0.03 Pa
  3. C5000 PaCorrect
  4. D10000 Pa

Why C is right

Pressure is force divided by area: P = F / A = 150 / 0.03 = 5000 Pa. The result follows from the fluid relationship or pressure/flow equation given in the problem. The result follows from the fluid relationship or pressure/flow equation given in the problem, so the pressure or force difference gives the answer.
Why the other 3 choices miss
A
Incorrect. This treats force as pressure and ignores the area over which the force acts.
B
Incorrect. This uses the area as if it were the pressure.
D
Incorrect. This is a common arithmetic error from dividing by a different area or dropping a zero.

Can you do all of these?

Tick what you can do without looking. Anything left unticked is where to go back to.

0 of 10 ticked

Ready to test yourself?

Open practice pulls from the 22 free questions in this unit. The other 35 come with the one-time AP purchase, which unlocks every AP course.

Official topic list

The official course framework breaks this unit into 4 numbered topics.

  1. 8.1Internal Structure and Density
  2. 8.2Pressure
  3. 8.3Fluids and Newton's Laws
  4. 8.4Fluids and Conservation Laws

Key terms in Fluids

Ordered by how often our reviewed questions test them. Open any term to see the questions that use it.

The rest of AP Physics 1

Every unit with its share of the exam. You are on Unit 7.

  1. 1Kinematics12.5% of exam
  2. 2Force and Translational Dynamics20.5% of exam
  3. 3Work, Energy, and Power20.5% of exam
  4. 4Linear Momentum12.5% of exam
  5. 5Torque and Rotational Dynamics; Energy and Momentum of Rotating Systems19% of exam
  6. 6Oscillations6.5% of exam
  7. 7Fluids12.5% of exam