Skip to content

Unit 3 of 7

Work, Energy, and Power

20.5% of the exam265 reviewed questions71 key terms17 min read

Work, Energy, and Power is worth about 20.5% of the AP Physics 1 exam. Our bank tests it with 265 reviewed questions across 71 distinct ideas — 102 easier, 116 medium and 47 harder.

On this page · 12 sections

This unit gives you a second way to solve motion problems. In Unit 2 you tracked forces and accelerations moment by moment. Here you track one number, energy, and compare where it starts with where it ends up. If a roller coaster drops 20 m, you do not need the shape of the track to find its speed at the bottom. You only need to know how much gravitational potential energy turned into kinetic energy, and how much friction took away along the way.

Three ideas hold the unit together. Work is how a force moves energy into or out of an object, and it equals force times displacement along the force's direction. The work-energy theorem says the net work done on an object equals its change in kinetic energy. Conservation of energy says the total energy of a system stays the same unless an outside force does work on it. Friction turns mechanical energy into thermal energy you can no longer use to move things. If the surface is outside your system, that loss shows up as negative work done on the system. Power adds time to the picture: it tells you how fast the energy moves.

This unit is about a fifth of the exam, tied with forces as the largest share. Most questions fall into a few patterns. You find a speed from a height or a spring compression. You find work from a force and an angle, or from the area under a graph. You account for energy lost to friction or a bounce. You find power from P = W/t or P = Fv. Many questions skip numbers entirely and ask how an answer changes when you double a mass or a height, so proportional reasoning matters as much as arithmetic.

The unit in a minute

One line per topic. Tap any line for the full notes.

  1. Work: force, displacement, and the angle between themOnly the force component along the motion does work; perpendicular forces do zero work, and opposing forces do negative work.
  2. Work from a graph: area and slopeOn a force-position graph, area is work and slope is k; on a force-time graph, area is impulse.
  3. Kinetic energy and the work-energy theoremNet work equals change in kinetic energy, and because K depends on v², doubling speed quadruples both K and stopping distance.
  4. Gravitational and spring potential energyU_g = mgh uses height change only and U_s = ½kx² uses stretch from natural length, so doubling h doubles U_g while doubling x quadruples U_s.
  5. Conservation of energy in roller coasters, ramps, and launchesWith no friction, K + U is constant, so final speed depends only on height drop and is independent of mass and path.
  6. Friction, energy loss, and efficiencyFriction converts mechanical energy to thermal energy in proportion to path length; efficiency multiplies the input to get the useful output.
  7. Power and simple machinesP = W/t or P = Fv; machines can multiply force only by shrinking distance, so work in equals work out when the machine is ideal.
Grind Work, Energy, and Power questionsAlready know this? Skip the notes and prove it.

The big ideas

Energy is bookkeeping, and you choose the system

Every energy problem starts with a choice: what is inside your system? If you include the Earth with a falling ball, gravity is internal, and you count gravitational potential energy (mgh). If you leave the Earth out, gravity becomes an outside force doing work on the ball, and you count that work instead of a potential energy. Both choices give the same answer, but you cannot do both at once. Counting mgh and also counting the work done by gravity counts the same energy twice. Pick the system first, then list what is inside it.

Work by outside forces changes a system's energy

In AP Physics 1, a system's energy changes when outside forces do work on it. Work is the transfer this course focuses on, and heating is another transfer that AP Physics 2 covers. A force does work only when it has a component along the displacement. W = Fd cos θ captures this. A force along the motion does positive work and adds energy. A force against the motion, like friction, does negative work and removes it. A force perpendicular to the motion, like the normal force on a flat floor or string tension on an object moving in a circle at constant speed, does zero work. The net work from all forces equals the change in kinetic energy. This is the work-energy theorem, and it is Newton's second law rewritten over a distance instead of over time.

Conservative forces store energy; friction does not

Gravity and spring forces are conservative. The work they do depends only on where you start and finish, not on the path. That is why you can define a potential energy for them: mgh for gravity and ½kx² for a spring. Energy you put in by lifting or stretching comes back when you let go. Friction is non-conservative. Its work depends on the length of the path, and the energy it removes turns into thermal energy, which does not come back as motion. When a question says energy is lost, it means energy has turned into a form you cannot use to move things.

Power is the rate, not the amount

Two climbers can do different amounts of work and still produce the same power if the one doing more work takes longer. Power is P = W/t, measured in watts (joules per second). When a force pushes something at a steady speed, P = Fv is often faster to use. Power questions test whether you can separate how much energy moved from how quickly it moved. A bigger engine does not make more energy available. It delivers that energy in less time.

Study notes

7 topics. Each one opens with its key idea, then the detail you need to use it.

1. Work: force, displacement, and the angle between them

Key idea: Only the force component along the motion does work; perpendicular forces do zero work, and opposing forces do negative work.

Work is W = Fd cos θ, where θ is the angle between the force and the displacement. Only the part of the force along the motion counts. Take a 10 kg block dragged 5 m across a rough floor by a rope at 37° above horizontal with 60 N of tension. The horizontal part of the tension is 60 × cos 37° = 48 N, so tension does 48 × 5 = 240 J. Friction of 30 N acts opposite the motion, so it does −30 × 5 = −150 J. The normal force and gravity are vertical while the motion is horizontal, so each does zero work. The net work is 240 − 150 = 90 J. The sign of work tells you the direction of the energy flow. Positive work adds energy to the object, and negative work takes it away. On an incline, gravity's work depends only on the vertical change. A block pushed 4 m up a 30° slope rises 4 sin 30° = 2 m. For a 3 kg block, gravity does −mgh = −(3)(10)(2) = −60 J. That answer is negative because gravity points down while the block moves up. The two most common slips are dropping the sign and using the slope length in place of the height.

2. Work from a graph: area and slope

Key idea: On a force-position graph, area is work and slope is k; on a force-time graph, area is impulse.

When a force changes as an object moves, W = Fd no longer works with a single value of F. Instead, the work equals the area under a force-versus-position graph. For a spring, the force grows in a straight line, F = kx, so the graph is a line through the origin. The area under it from 0 to x is a triangle with base x and height kx. Its area is ½ × x × kx = ½kx², which is exactly the elastic potential energy stored in the spring. That is not a coincidence. The work you do stretching the spring is the energy it stores. Read the graph features carefully because each one means something different. On a spring's F-x graph, the slope is the spring constant k, and the area is work or energy. On a force-time graph, the area is impulse, which belongs to the momentum unit. The area under an F-x graph is never power, because the graph has no time on it. For curved graphs, estimate the area by counting grid squares or splitting the region into triangles and rectangles. Area below the axis counts as negative work. A common trap reads a single force value off the graph and multiplies it by the full distance, which ignores how the force changed along the way.

3. Kinetic energy and the work-energy theorem

Key idea: Net work equals change in kinetic energy, and because K depends on v², doubling speed quadruples both K and stopping distance.

Kinetic energy is K = ½mv². Because speed is squared, it controls the answer more than mass does. Double the speed and K becomes four times larger. Triple it and K becomes nine times larger. Run this backwards when you know the energy and need the speed: v = √(2K/m). Four times the kinetic energy only doubles the speed. The work-energy theorem says W_net = ΔK. Add up the work from every force, including signs, and that total equals the change in kinetic energy. This explains braking distance. Friction from the brakes does negative work, −fd, which must cancel the car's kinetic energy. If the braking force stays the same, the stopping distance d is proportional to v². A car going twice as fast needs four times the distance to stop. The theorem also explains constant-speed motion. If speed does not change, ΔK = 0, so the net work is zero. The positive work done by an engine is cancelled exactly by the negative work done by drag and friction. That does not mean no force acts. It means the forces balance in their energy effect. Use this theorem when a question gives you forces and distances and asks for a speed.

4. Gravitational and spring potential energy

Key idea: U_g = mgh uses height change only and U_s = ½kx² uses stretch from natural length, so doubling h doubles U_g while doubling x quadruples U_s.

Potential energy is energy stored in the arrangement of a system. Near Earth's surface, gravitational potential energy is U_g = mgh, where h is height above a reference level you choose. Only changes in height matter, so put zero wherever it makes the math easiest, often at the lowest point. Lifting a 2 kg box 3 m raises its potential energy by 2 × 10 × 3 = 60 J, whatever path you carry it along. The mgh formula is a near-surface approximation, and for widely separated objects such as a planet and a satellite, the exam can use U_G = −Gm₁m₂/r instead. Spring potential energy is U_s = ½kx², where x is the stretch or compression from the spring's natural length. It is not the spring's total length. Because x is squared, compressing a spring twice as far stores four times the energy. A stretched spring and a compressed spring with the same x store the same energy. Springs can combine. Two identical springs side by side, each compressed by x, act like one spring with constant 2k, so together they store ½(2k)x² = kx². You can reach the same answer by adding the two springs' energies: 2 × ½kx². Potential energy graphs show U against position. Where U is lowest, kinetic energy is highest, so the object moves fastest there. A turning point sits where the total energy line crosses the U curve, because K equals zero at that spot.

5. Conservation of energy in roller coasters, ramps, and launches

Key idea: With no friction, K + U is constant, so final speed depends only on height drop and is independent of mass and path.

If only conservative forces do work inside your system, mechanical energy stays constant: K_i + U_i = K_f + U_f. A cart released from rest at height h on a frictionless track reaches the bottom with mgh = ½mv², so v = √(2gh). Mass cancels. A heavy cart and a light cart reach the same speed, which the exam tests often. Track shape does not matter either. A steep drop and a gentle slope of the same height give the same final speed. The steep one simply gets there sooner. Maximum speed occurs where potential energy is lowest. For a coaster, that is the lowest point of the track. For a mass on a horizontal spring, it is the point where the spring is at its natural length and U_s = 0. Springs launching objects work the same way: ½kx² = ½mv² on a level surface, or ½kx² = mgh if the object rises to a stop. A mass at rest at the top of its path has zero kinetic energy. A projectile at the top of its arc still moves sideways, so it does not. Set up each problem by listing every energy form at the start and at the end, then setting the totals equal.

6. Friction, energy loss, and efficiency

Key idea: Friction converts mechanical energy to thermal energy in proportion to path length; efficiency multiplies the input to get the useful output.

When friction acts, mechanical energy is not conserved, but total energy still is. Write it as K_i + U_i − fd = K_f + U_f, where fd is the energy friction turns into thermal energy. Friction always removes mechanical energy, and the amount grows with the length of the sliding path. A longer, gentler ramp of the same height loses more energy to friction than a short steep one with the same friction force. Efficiency is the fraction of input energy that becomes useful output. A toy car's spring holds 500 J and the car is 80% efficient, so 400 J becomes kinetic energy. With a mass of 0.5 kg, ½(0.5)v² = 400 gives v² = 1600, so v = 40 m/s. Use 400 J, not the full 500 J. A bouncing ball shows energy loss clearly. If a ball dropped from 2.0 m rebounds to 1.5 m, it kept 75% of its mechanical energy. The other 25% went into sound, heat and the ball's deformation during the collision. Each later bounce loses a fraction of what is left, so the rebound heights shrink. A ball can never rebound higher than it was dropped from unless something adds energy. Any answer that ends with more energy than the start is wrong.

7. Power and simple machines

Key idea: P = W/t or P = Fv; machines can multiply force only by shrinking distance, so work in equals work out when the machine is ideal.

Power is the rate of energy transfer: P = W/t = ΔE/t. One watt is one joule per second. A 500 MW power plant running for one hour (3600 s) delivers 5 × 10⁸ × 3600 = 1.8 × 10¹² J. Convert hours and minutes to seconds before you divide. For a force pushing at a steady speed, P = Fv. A car moving at a constant 25 m/s with a 40 kW engine faces a resistive force of 40,000/25 = 1600 N. At constant speed, the engine force equals the resistive force. In lifting problems, add every force the motor must overcome. An elevator of 500 kg rising at 2 m/s against 1000 N of friction needs a force of 5000 + 1000 = 6000 N, so the power is 6000 × 2 = 12,000 W. Leave out either term and you get a tempting wrong answer. Power comparisons often hide a tie. A 50 kg climber rising 30 m in 600 s produces 25 W, and a 75 kg climber rising 30 m in 900 s also produces 25 W. Simple machines trade force for distance but never create energy. An ideal ramp 3 m long that lifts a 600 N box 1.5 m needs F × 3 = 600 × 1.5, so the push is 300 N. A lever with mechanical advantage 4 multiplies force by 4 and divides distance by 4.

Common mistakes

Drawn from the wrong answers students actually pick on these questions.

Treating the area under a force-position graph as power, impulse, or the spring constant.

Area under F vs. x is work, which for a spring equals the stored energy ½kx². The slope of that line is k. Impulse is the area under a force-time graph, and power needs a time, which an F-x graph does not show.

Leaving out one force when finding the power a motor needs to lift a load against friction.

The motor must supply a force equal to the weight plus the friction force when it lifts at constant speed. Add them first, then use P = Fv. Using only mg or only friction gives answers that are too small.

Using the full input energy when only part of it becomes kinetic energy.

Multiply by the efficiency before you solve for speed. With 80% of 500 J, use 400 J in ½mv². A speed that gives more kinetic energy than the original energy store is impossible.

Assuming a simple machine that multiplies force keeps the same distance, or that it reduces the output force.

For an ideal machine, input work equals output work. With mechanical advantage 4, the load force is 4 times the input force and it moves one quarter of the distance. You gain force only by giving up distance.

Dropping the negative sign on gravity's work when an object moves upward, or using the slope length in place of the height.

Gravity does −mgh when an object rises, because the force points down and the motion points up. On an incline, h is the vertical rise, d sin θ, not the distance along the slope and not twice that rise.

Multiplying a single force value by the whole distance when the force changes along the path.

When force varies, work equals the area under the F-x graph. For a spring, that area is a triangle, so the work is ½kx², not kx × x. Using the largest force overestimates the work. Averaging just the starting and ending force values works only for a straight-line graph, so for a curved graph, find the area.

How this unit shows up on the exam

Expect this unit in roughly a fifth of the exam's multiple-choice questions. Each has four answer choices, and the wrong ones are built from the mistakes above: a missing sign, a forgotten force, the full energy where only part should count. Stems come in a few recognisable shapes. "An object is released from rest at height h…" asks for a speed through conservation of energy. "A block slides along a rough surface…" adds a friction term, fd. "The graph shows force as a function of position…" wants an area. "An engine moves the car at constant speed…" points you to P = Fv and balanced forces. Many questions use no numbers at all. They ask what happens to the final speed, the stopping distance or the stored energy if one quantity doubles, so practise saying "v depends on √h, so doubling h multiplies v by about 1.41."

The free-response section rewards clear reasoning more than final numbers. You may be asked to sketch energy bar charts that show K, U_g and U_s at two moments, plus any energy friction removes. You may also have to defend in words why a speed is or is not independent of mass. Readers want you to name the system, say which forces do work on it, and write the conservation equation before you substitute numbers. If a part asks you to justify an answer, a correct equation with a one-line reason, such as "no friction, so mechanical energy is conserved", usually beats a page of algebra. Experimental questions in this unit often ask you to graph a quantity so the result is a straight line. Plotting h against v² for a cart on a ramp is one example, and its slope then relates to 1/(2g). AP Physics 1 is algebra-based. You will find work from graph areas built from triangles and rectangles, not by integrating, and you get an equation sheet with K, U_g, U_s, W and P on it.

How the exam actually asks it

Real items from the AP Physics 1 bank, easier first. The answer is marked, and every wrong choice is explained — because knowing why a distractor is tempting is most of the work.

Worked example 1Easier
Which of the following forces is conservative?
  1. AAir resistance
  2. BGravitational forceCorrect
  3. CKinetic friction
  4. DApplied force by a person

Why B is right

A conservative force does work that depends only on the initial and final positions, not the path taken. Gravitational force is conservative because the work done by gravity depends only on the change in height.
Why the other 3 choices miss
A
Incorrect. Air resistance is non-conservative for the same reason as friction: it depends on the path through which the object moves.
C
Incorrect. Kinetic friction is non-conservative because the work it does depends on the path length; longer paths result in more energy lost to friction.
D
Incorrect. An applied force by a person is generally non-conservative because it can do varying amounts of work depending on the path and how it is applied.
Worked example 2Easier
An energy bar chart shows a ball at height with of gravitational PE and of KE. At the bottom (), what does the bar chart show if is lost to air resistance during the fall?
  1. A
  2. B
  3. CCorrect
  4. D

Why C is right

At the bottom, (since ). The total mechanical energy was , but was lost to air resistance (converted to thermal energy). Thus . The result follows from conservation of energy or the work-energy relationship, so the change in kinetic or potential energy sets the answer.
Why the other 3 choices miss
A
Incorrect. At the bottom, because . Energy does not split equally between KE and PE.
B
Incorrect. At , the gravitational PE is , not . The lost energy becomes thermal energy, not potential energy.
D
Incorrect. This assumes no energy loss, which contradicts the stated lost to air resistance.
Worked example 3Easier
A 3 kg object is thrown vertically upward with an initial speed of 20 m/s. Using energy methods, what is the maximum height reached? Use g = 10 m/s^2.
  1. A40 m
  2. B15 m
  3. C10 m
  4. D20 mCorrect

Why D is right

At maximum height, all KE converts to PE: (1/2)mv^2 = mgh. h = v^2/(2g) = 400/20 = 20 m. The mass cancels and is not needed. The result follows from conservation of energy or the work-energy relationship, so the change in kinetic or potential energy sets the answer.
Why the other 3 choices miss
A
Incorrect. This uses h = v^2/g = 400/10 = 40, forgetting the factor of 2 in the denominator.
B
Incorrect. This does not correctly apply the energy conservation equation.
C
Incorrect. This uses h = v/2g with v = 20 and misses the squaring of v.
Worked example 4Easier
A ball falls from rest through a height of and bounces off the floor, rising to a height of . How much energy is lost during the bounce? Use .
  1. A
  2. BCorrect
  3. C
  4. D

Why B is right

before bounce . after bounce . Energy lost . The result follows from conservation of energy or the work-energy relationship, so the change in kinetic or potential energy sets the answer.
Why the other 3 choices miss
A
Incorrect. This is one-tenth of the correct answer, possibly from using the wrong mass ( instead of ).
C
Incorrect. is the energy after the bounce, not the energy lost.
D
Incorrect. is the total initial energy. The bounce is not perfectly inelastic; the ball retains .

Can you do all of these?

Tick what you can do without looking. Anything left unticked is where to go back to.

0 of 10 ticked

Ready to test yourself?

Open practice pulls from the 35 free questions in this unit. The other 230 come with the one-time AP purchase, which unlocks every AP course.

Official topic list

The official course framework breaks this unit into 5 numbered topics.

  1. 3.1Translational Kinetic Energy
  2. 3.2Work
  3. 3.3Potential Energy
  4. 3.4Conservation of Energy
  5. 3.5Power

Key terms in Work, Energy, and Power

Ordered by how often our reviewed questions test them. Open any term to see the questions that use it.

Kinetic energy61 questionsEnergy conservation59 questionsFriction52 questionsPower45 questionsWork energy theorem36 questionsConservation of energy33 questionsWork30 questionsSpring24 questionsgravitational PE22 questionsSpeed18 questionsIncline17 questionsConceptual15 questionsPotential energy15 questionsspring PE13 questionsEnergy loss12 questionsMaximum speed11 questionsBounce10 questionsConservative force10 questionsNet work10 questionsProportionality10 questionsRoller coaster9 questionsEnergy conversion8 questionsLifting8 questionsProportional reasoning8 questionsBraking7 questionsComparison7 questionsEfficiency7 questionsEnergy7 questionsHeight7 questionsPotential energy graph7 questionsThermal energy7 questionsWork against gravity7 questionsCalculation6 questionsCoefficient of restitution6 questionselastic PE6 questionsEnergy efficiency6 questionsAir resistance5 questionsAngle5 questionsBraking distance5 questionsEnergy transfer5 questionsForce5 questionsSpring launcher5 questionsTime5 questionsGravitational potential energy4 questionsMechanical advantage4 questionsMotor4 questionsOrbital energy4 questionsQuadratic4 questionsResistive force4 questionsSimple machines4 questionsSpring energy4 questionsStopping distance4 questionsUnit conversion4 questionsWork energy4 questionsApplied force3 questionsClimbing3 questionsConstant speed3 questionsElastic potential energy3 questionsEnergy bar chart3 questionsEscape velocity3 questionsForce displacement graph3 questionsFriction loss3 questionsLoop3 questionsNegative work3 questionsNon conservative force3 questionsP equals Fv3 questionsRamp3 questionsRube Goldberg3 questionsSpring compression3 questionsVariable force3 questionsWork by gravity3 questions

The rest of AP Physics 1

Every unit with its share of the exam. You are on Unit 3.

  1. 1Kinematics12.5% of exam
  2. 2Force and Translational Dynamics20.5% of exam
  3. 3Work, Energy, and Power20.5% of exam
  4. 4Linear Momentum12.5% of exam
  5. 5Torque and Rotational Dynamics; Energy and Momentum of Rotating Systems19% of exam
  6. 6Oscillations6.5% of exam
  7. 7Fluids12.5% of exam