A 2 kg book is pressed against a wall by a horizontal force of 40 N. The coefficient of static friction between the book and wall is 0.6. Does the book slide? (g = 10 m/s^2)
- AYes, because the weight (20 N) exceeds the horizontal applied force.
- BNo, because the normal force cancels gravity.
- CYes, because horizontal force cannot support vertical weight.
- DNo, because friction (24 N) exceeds the book's weight (20 N).Correct
Why D is right
The book is pressed against the wall with N = 40 N (horizontal applied force acts as normal force here). Maximum static friction = mu_s * N = 0.6 * 40 = 24 N (acting upward). Weight = mg = 2*10 = 20 N (acting downward). Since 24 N > 20 N, friction can support the weight and the book does NOT slide.
Why the other 3 choices miss
- A
- Incorrect because the applied force creates a normal force that enables friction; the comparison should be between friction and weight, not applied force and weight.
- B
- Incorrect because the normal force from the wall is horizontal, not vertical; it is friction (not normal force) that counteracts gravity here.
- C
- Incorrect because friction (vertical) can support vertical weight; the horizontal force provides the normal force that enables sufficient friction.
A 10 kg block sits on top of a 20 kg block that rests on a frictionless floor. A horizontal force is applied to the bottom block. The coefficient of static friction between the blocks is 0.4. What is the maximum force that can be applied to the bottom block before the top block starts to slip? (Use g = 10 m/s^2.)
- A120 NCorrect
- B60 N
- C40 N
- D20 N
Why A is right
The top block can be accelerated by friction only. Maximum friction on top block: f_s,max = mu_s * m_top * g = 0.4 * 10 * 10 = 40 N. Maximum acceleration before slipping: a_max = f_s,max / m_top = 40/10 = 4 m/s^2. For the whole system to have this acceleration: F = (m_top + m_bottom) * a = 30 * 4 = 120 N.
Why the other 3 choices miss
- B
- Incorrect because 60 N might result from applying the friction force to only 2/3 of the system mass without proper analysis.
- C
- Incorrect because 40 N is the maximum friction force on the top block alone, not the maximum force on the combined system.
- D
- Incorrect because 20 N is far too small; it does not account for the system mass or friction correctly.
A car going around a curve at constant speed on a flat road relies on friction for centripetal force. If the road is wet and friction is reduced to half, what happens to the maximum safe speed for the same curve?
- AThe maximum speed is halved.
- BThe maximum speed is reduced to 1/4 of the original.
- CThe maximum speed is reduced to 1/sqrt(2) of the original.Correct
- DThe maximum speed does not change because the curve radius is the same.
Why C is right
Maximum speed from centripetal condition: v_max = sqrt(mu_s * g * r). If mu_s is halved: v_max_new = sqrt((mu_s/2)*g*r) = v_max / sqrt(2) ≈ 0.707 * v_max. The maximum safe speed is reduced by a factor of 1/sqrt(2).
Why the other 3 choices miss
- A
- Incorrect because speed scales as sqrt(mu_s), not mu_s directly; halving mu_s reduces speed by 1/sqrt(2), not 1/2.
- B
- Incorrect because reducing speed to 1/4 would correspond to mu_s being reduced to 1/16, not 1/2; the relationship is v ∝ sqrt(mu_s).
- D
- Incorrect because the maximum safe speed depends on the friction coefficient; if friction is reduced, the maximum speed decreases.