Experiment 3: A student investigated how temperature affects the viscosity of motor oil, using a falling-ball viscometer. The time for a steel ball to fall 10 cm through oil was recorded:
Temperature (°C) | Falling Time (s) | Calculated Viscosity (cP)
0 | 148 | 2,958
20 | 38 | 760
40 | 14 | 280
60 | 6.8 | 136
80 | 3.9 | 78
100 | 2.6 | 52
A car engine operates at approximately 90°C. Based on the data, what is the approximate viscosity of the motor oil at operating temperature?
- A78 cP
- B52 cP
- C136 cP
- D65 cPCorrect
Why D is right
At 80°C, viscosity = 78 cP. At 100°C, viscosity = 52 cP. For 90°C (midpoint between 80°C and 100°C), interpolate: (78 + 52) / 2 = 65 cP. The data and relationship in the passage point to this result more directly than the other choices.
Why the other 3 choices miss
- A
- Incorrect because 78 cP corresponds to 80°C; at 90°C (higher temperature), viscosity is lower than 78 cP.
- B
- Incorrect because 52 cP corresponds to 100°C, not 90°C; at 90°C (between 80 and 100°C), viscosity is between 52 and 78 cP.
- C
- Incorrect because 136 cP corresponds to 60°C; at 90°C, viscosity has dropped well below this value.
A student measured the terminal velocity of spherical balls of different diameters falling through glycerol in a cylinder. Stokes' Law applies for slow viscous flow: v_terminal = (2r²(ρ_ball − ρ_fluid)g) / (9η), where r = radius, ρ = density, g = 9.8 m/s², and η = dynamic viscosity. Results with glass balls (ρ_glass = 2,500 kg/m³) in glycerol (ρ_glycerol = 1,260 kg/m³, η = 1.48 Pa·s): Diameter (mm) / Terminal velocity (mm/s): 2 mm: 1.84. 4 mm: 7.35. 6 mm: 16.6. 8 mm: 29.5. What is the predicted terminal velocity for a 10 mm diameter glass ball?
- A55 mm/s
- B64 mm/s
- C46 mm/sCorrect
- D37 mm/s
Why C is right
From Stokes' Law, v ∝ r². When diameter doubles from 2 to 4 mm (r: 1 to 2 mm), v increases by 2² = 4: 1.84 × 4 = 7.36 mm/s. ✓ When d goes from 2 to 10 mm (r: 1 to 5 mm), v increases by 5² = 25: 1.84 × 25 = 46.0 mm/s ≈ 46 mm/s. Alternatively: from 8 mm (v = 29.5), to 10 mm: factor = (5mm/4mm)² = 25/16 = 1.5625; 29.5 × 1.5625 = 46.1 mm/s.
Why the other 3 choices miss
- A
- Incorrect because 55 mm/s would require a larger r-scaling factor than r² predicts; 10 mm vs 8 mm gives a factor of (5/4)² = 1.5625, not the 1.86 needed for 55 mm/s.
- B
- Incorrect because 64 mm/s would require v to scale faster than r², which contradicts Stokes' Law for viscous flow.
- D
- Incorrect because 37 mm/s corresponds to r scaling inconsistent with Stokes' Law; 10 mm diameter gives a higher velocity than the 8 mm ball (29.5 mm/s).
A materials scientist measures the viscosity of four liquids at temperatures ranging from 0°C to 80°C. The data table below shows viscosity (in mPa·s) at each temperature:
Temperature (°C) | Water | Glycerol | Mercury | Air
0 | 1.79 | 12,100 | 1.69 | 0.0171
20 | 1.00 | 1,410 | 1.55 | 0.0181
40 | 0.65 | 284 | 1.45 | 0.0190
60 | 0.47 | 81 | 1.37 | 0.0200
80 | 0.36 | 31 | 1.29 | 0.0208
Which of the following statements is supported by the data?
- AAll four substances show increasing viscosity as temperature increases from 0°C to 80°C.
- BAir viscosity decreases as temperature increases, unlike the other substances.
- CWater and glycerol lose viscosity when heated, while air gains viscosity.Correct
- DMercury becomes less viscous as temperature increases, but water becomes more viscous.
Why C is right
Water, glycerol, and mercury all show decreasing viscosity as temperature increases (typical of liquids, where heat disrupts intermolecular forces). Air (a gas) shows increasing viscosity with temperature — in gases, higher temperature increases molecular collisions, raising viscosity.
Why the other 3 choices miss
- A
- Incorrect; the table clearly shows that water, glycerol, and mercury all decrease in viscosity with temperature.
- B
- Incorrect; air viscosity increases with temperature (from 0.0171 to 0.0208 mPa·s) — the opposite of the liquids.
- D
- Incorrect; both mercury and water decrease in viscosity with temperature according to the table.