Table 3 shows the results of testing four different insulation materials in a standardized thermal resistance experiment. Each material (same thickness: 10 cm) was placed between a heat source at 80°C and a cold surface at 20°C:
Material | Thermal Conductivity (W/m·K) | Temperature at cold surface after 1 hr (°C)
Fiberglass | 0.040 | 21.8
Cellulose | 0.038 | 21.7
Spray foam | 0.026 | 20.8
Aerogel | 0.015 | 20.4
Note: Lower thermal conductivity = better insulator.
A homeowner wants the most effective insulation. Based on the data, which material should be chosen?
- AFiberglass
- BSpray foam
- CAerogelCorrect
- DCellulose
Why C is right
Aerogel has the lowest thermal conductivity (0.015 W/m·K), meaning it transmits the least heat. This is confirmed by the lowest cold-surface temperature after 1 hour (20.4°C, closest to the starting 20°C), indicating minimal heat transfer through the aerogel insulation.
Why the other 3 choices miss
- A
- Incorrect because fiberglass has the highest thermal conductivity (0.040 W/m·K) of the four materials, making it the least effective insulator in this comparison.
- B
- Incorrect because spray foam (0.026 W/m·K) is better than fiberglass and cellulose but still less effective than aerogel (0.015 W/m·K).
- D
- Incorrect because cellulose has the second-highest conductivity (0.038 W/m·K) and cold-surface temperature (21.7°C), indicating it is the second-least effective insulator.
Experiment 4: A materials scientist tested the tensile strength (maximum stress before fracture) and percent elongation (ductility) of four metal alloys.
Alloy | Tensile Strength (MPa) | Percent Elongation (%)
Steel A | 820 | 18
Steel B | 1,250 | 8
Aluminum alloy | 480 | 22
Titanium alloy | 950 | 14
An aerospace engineer needs a material that is both strong (≥900 MPa tensile strength) AND ductile (≥12% elongation). Which alloy meets both requirements?
- AAluminum alloy
- BSteel B
- CSteel A
- DTitanium alloyCorrect
Why D is right
Titanium alloy has a tensile strength of 950 MPa (≥900 MPa requirement met) and 14% elongation (≥12% requirement met). It is the only alloy satisfying both criteria simultaneously.
Why the other 3 choices miss
- A
- Incorrect because the aluminum alloy has only 480 MPa tensile strength, far below the 900 MPa requirement, even though it exceeds the ductility requirement at 22% elongation.
- B
- Incorrect because Steel B has sufficient strength (1,250 MPa) but only 8% elongation, falling short of the 12% ductility requirement.
- C
- Incorrect because Steel A has only 820 MPa tensile strength, which falls below the 900 MPa requirement, even though its elongation (18%) meets the ductility requirement.
Figure 3 describes a graph of electrical resistance (y-axis, in Ohms) versus temperature (x-axis, in Kelvin, 0–300K) for three materials: a metal (steadily decreasing resistance as temperature drops), a semiconductor (resistance decreasing dramatically as temperature rises), and a superconductor (resistance drops to exactly zero below a critical temperature Tc ≈ 10K).
At room temperature (approximately 300K), which material has the lowest resistance based on typical behavior?
- AThe semiconductor, because its resistance decreases with rising temperature.
- BThe metal, because metals are excellent conductors at all temperatures.Correct
- CThe metal, because its resistance is lower at high temperatures than at very low temperatures.
- DThe superconductor, because its resistance drops to zero below 10K.
Why B is right
At room temperature (300K), metals typically have low electrical resistance and are the best conductors at this temperature. The superconductor only achieves zero resistance below 10K (far below room temperature), and semiconductors generally have higher resistance than metals at room temperature.
Why the other 3 choices miss
- A
- Incorrect because while semiconductors do conduct better at higher temperatures, their resistance at room temperature is still typically much higher than that of metals.
- C
- Incorrect reasoning: the question asks about room temperature, not a comparison across temperatures. At room temperature, metal resistance is low and relatively constant — the comparison to 'very low temperatures' is irrelevant to the question.
- D
- Incorrect because at 300K the superconductor has not yet reached its critical temperature (10K) and behaves like a normal material with non-zero resistance.